-
Schuett Dassault
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
Greg Schoeppner CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Jack Gillespie CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Jacob Fish Columbia CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Jerry Young Boeing CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Pascal Hubert CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
The Challenge and Vision for cdmHUB
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Puck Failure Criteria
31 Jul 2017 | Downloads
Composite materials have been established as competitive materials during the last few decades due to their high strength to l ow weight ratio among other advantages and are widely used in many industries. A recent study has found that the industrial usage of composite failure...
-
Orthotropic Stress Concentration Factor
25 Sep 2014 | Tools
Calculates the stress concentration factor for a circular hole in an infinite orthotropic plate
-
CDM Hub Introduction
31 Aug 2024 | Online Presentations | Contributor(s): SME Project
-
The Mission, Vision and Programs of the Composites Design and Manufacturing HUB
31 Aug 2024 | Teaching Materials | Contributor(s): SME Project
The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.
-
The Mission, Vision and Programs of the Composites Design and Manufacturing HUB
22 May 2013 | Teaching Materials
The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.
-
The Mission, Vision and Programs of the Composites Design and Manufacturing HUB
25 Sep 2014 | Teaching Materials
The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.
-
Plane-Stress Compliance Transform
25 Sep 2014 | Tools
Transforms 2D compliance terms by rotation about the 3-axis
-
Composite Materials and Structures 1972-2012: Grand Challenges
22 May 2013 | Teaching Materials
Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.
-
2013 Composites Design and Manufacturing HUB Kickoff Workshop
31 Aug 2024 | Series | Contributor(s): SME Project
The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government. Select presentations from the workshop are included in this series.
-
2013 Composites Design and Manufacturing HUB Kickoff Workshop
22 May 2013 | Series
The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government. Select presentations from the workshop are included in this series.
-
HyperSizer Pro Software from Collier Research
22 May 2013 | Tool Information
HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...
-
Nanohub and the HUBzero Platform
31 Aug 2024 | Online Presentations | Contributor(s): SME Project
Dr. Michael McLennan describes the nanoHUB and HUBzero platform at the May 2013 Composites Design and Manufacturing HUB workshop.
-
The Challenge and Vision for cdmHUB
31 Aug 2024 | Online Presentations | Contributor(s): SME Project
Professor R. Byron Pipes presents the challenge and vision for the cdmHUB at the May 2013 Composites Design and Manufacturing HUB workshop