-
2013 Composites Design and Manufacturing HUB Kickoff Workshop
04 Sep 2014 | Series | Contributor(s): SME Project
The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government. Select presentations from the workshop are included in this series.
-
2013 Composites Design and Manufacturing HUB Kickoff Workshop
04 Sep 2014 | Series
The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government. Select presentations from the workshop are included in this series.
-
2015 cdmHUB Workshop
05 Jan 2016 | Series
Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015. Both lectures slides and lecture videos are presented.
-
2015 cdmHUB Workshop
05 Jan 2016 | Series
Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015. Both lectures slides and lecture videos are presented.
-
Anousch Poursartip UBC CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
CDM HUB Breakout Sessions
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Breakout sessions from the May 2013 Composites Design and Manufacturing HUB workshop
-
CDM Hub Breakout Sessions 1 and 2 B-Roll
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
CDM Hub Breakout Sessions Introduction
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
CDM Hub Introduction
17 Mar 2015 | Online Presentations | Contributor(s): SME Project
-
Chuck Tucker UIUC CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Composite Materials and Structures 1972-2012: Grand Challenges
19 Sep 2014 | Teaching Materials
Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.
-
Composite Stiffness Property Prediction
07 Aug 2017 | Downloads
Micromechanical models for the composite axial tensile, transverse tensile, and axial shear are combined into one tool with the objective of comparing their effectiveness as property prediction methods. Rule of mixtures models (ROM) and the composite cylinder model (CCM) results for...
-
Computational evaluation of effective stress relaxation behavior of polymer composites
11 Jul 2017 | Publications
This paper presents a micromechanics model to characterize the effective stress relaxationstiffness of polymer composites. The linear viscoelastic behavior of polymer material wasmodeled by hereditary integral. The proposed model was established based on thevariational asymptotic method for unit...
-
Effective Lamina and Laminate Properties
10 Oct 2013 | Tools
Calculate effective lamina and laminate properties from phase properties and layup.
-
Finite element unit cell model based on ABAQUS for fiber reinforced composites
10 Oct 2013 | Downloads
-
Gillespie CCM
17 Aug 2024 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
Greg Schoeppner CDM Hub
17 Aug 2024 | Online Presentations | Contributor(s): SME Project
-
Halpin-Tsai Micromechanics Model
10 Oct 2013 | Tools
Calculate homogenized lamina properties from fiber and matrix properties
-
Hubert McGill
17 Aug 2024 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
HyperSizer Pro Software from Collier Research
23 Jul 2014 | Tool Information
HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...