-
Hubert McGill
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
HyperSizer Pro Software from Collier Research
20 Aug 2014 | Tool Information
HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...
-
Interlaminar Stresses in Symmetric Angle-Ply Laminates Subjected to Anticlastic Bending Deformation
04 Jun 2014 | Tool Information
The aim of the present work is to develop a solution for the interlaminar stress field in a symmetric and balanced, angle-ply laminate subjected to anticlastic bending deformation. Further, this class of problems is considered in order to elucidate the behavior of angle-ply laminates...
-
Jack Gillespie CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Jacob Fish Columbia CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Jerry Young Boeing CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Nanohub and the HUBzero Platform
16 Aug 2014 | Online Presentations | Contributor(s): SME Project
Dr. Michael McLennan describes the nanoHUB and HUBzero platform at the May 2013 Composites Design and Manufacturing HUB workshop.
-
Ove Schuett Dassault Systemes Americas CDM Hub
18 Jul 2019 | Online Presentations | Contributor(s): SME Project
-
Pascal Hubert CDM Hub
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
Poursartip UBC
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
Puck Failure Criteria
31 Jul 2017 | Downloads
Composite materials have been established as competitive materials during the last few decades due to their high strength to l ow weight ratio among other advantages and are widely used in many industries. A recent study has found that the industrial usage of composite failure...
-
Schoeppner AFRL
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop.
-
Schuett Dassault
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop
-
The Challenge and Vision for cdmHUB
14 Aug 2014 | Online Presentations | Contributor(s): SME Project
Professor R. Byron Pipes presents the challenge and vision for the cdmHUB at the May 2013 Composites Design and Manufacturing HUB workshop
-
The Challenge and Vision for cdmHUB
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
-
The Mission, Vision and Programs of the Composites Design and Manufacturing HUB
08 Oct 2014 | Teaching Materials | Contributor(s): SME Project
The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.
-
The Mission, Vision and Programs of the Composites Design and Manufacturing HUB
08 Oct 2014 | Teaching Materials
The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.
-
Woven fabrics UMAT- a coupled material model
02 Aug 2017 | Downloads | Contributor(s): Ali Roumani
One of the advantages of woven fabrics over unidirectional prepregs is their superior formability thanks to the large shear deformation capability. There exists, however, a limit on the shear deformation of woven fabrics, namely the wrinkling. Applying tension to delay wrinkling during forming...
-
Young Boeing
15 Feb 2019 | Online Presentations | Contributor(s): SME Project
Presentation at the May 2013 Composites Design and Manufacturing HUB workshop