Injection Overmolding Manufacturing Process Simulation

29 Jun 2017 | Online Presentations

Injection over-molding or hybrid molding is a high-rate composites manufacturing process for fabrication of structural components with complex geometries.  The structural backbone is provided by a continuous-fiber woven prepreg while the geometric complexity is realized via injection...

Orthotropic Stress Concentration Factor

25 Sep 2014 | Tools

Calculates the stress concentration factor for a circular hole in an infinite orthotropic plate

Analysis of Slender Structures Using Mechanics of Structure Genome and Open Source Codes

28 May 2014 | Publications

This is the Master thesis from Xin Liu in Prof Yu’s research group. In this thesis, the Mechanics of Structure Genome (MSG) has be used to provide an alternative way to model composite beam-like structures. Basic concept of MSG is introduced as well as the idea of how to carry out...

2015 cdmHUB Workshop

23 Jul 2014 | Series

Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

2015 cdmHUB Workshop

23 Jul 2014 | Series

Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

2015 cdmHUB Workshop

23 Jul 2014 | Series

Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

2015 cdmHUB Workshop

28 May 2014 | Series

Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

HyperSizer for Composites: Insanely Fast Laminate Optimization

28 May 2014 | Tool Information

95% of users, without user manual, and without instruction, will be able to import their FEM and produce optimum composites laminates that satisfy all analyses to all load cases within the first 10 minutes. Your automatically updated model will have minimum weight and fully producible laminates...

NAFEMS Invitation to Tender: How to Obtain Material Properties for Structural Analysis of Composites

23 Jul 2014 | White Papers/Research Documents

The NAFEMS Composites Working Group wishes to commission a new document with the suggested title "How to Obtain Material Properties for Structural Analysis of Composites". The book will be a companion volume to the existing NAFEMS publications "An introduction to the use of material models in...

Structure Genome: Fill the Gap between Materials Genome and Structural Analysis

28 May 2014 | Publications

A new concept, Structure Genome (SG), is proposed to fill the gap between materials genome and structural analysis. SG acts as the basic building block of the structure connecting materials to structures and the mechanics of SG governs the necessary information to link materials genome and...

Variational Asymptotic Modeling of Composite Dimensionally Reducible Structures

28 May 2014 | Publications

This is Prof. Yu's PhD dissertation. In this disseration, the variational asymptotic method has be used to provide a systematic, holistic, and rigorous approach to construct efficient yet accurate models for composite beams, plates, and shells.  

DiBenedetto Equation: Tg and DOC

23 Jul 2014 | Tools

DiBenedetto Equation: Glass Transition Temperature Dependence on Degree of Cure

The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

25 Sep 2014 | Teaching Materials

The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

23 Jul 2014 | Teaching Materials

The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

28 May 2014 | Teaching Materials

The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

Plane-Stress Compliance Transform

25 Sep 2014 | Tools

Transforms 2D compliance terms by rotation about the 3-axis

Keith Kedward and Composites Design (Slides)

23 Jul 2014 | Teaching Materials

Professor Byron Pipes' slides from the 2014 ASC meeting at UCSD discussing Keith Kedward and Composites Design

Keith Kedward and Composites Design (Recorded Talk)

23 Jul 2014 | Teaching Materials

Professor Byron Pipes speaks at the 2014 ASC Conference at UCSD in tribute to Keith Kedward on the subject of Composites Design.

Composite Materials and Structures 1972-2012: Grand Challenges

23 Jul 2014 | Teaching Materials

Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

Composite Materials and Structures 1972-2012: Grand Challenges

23 Jul 2014 | Teaching Materials

Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.