Resources: All

Submit a resource

Find a resource
  1. compositesmanufacturing x
  2. compositesanalysis x
  3. prepregplateletcomposites x
  4. compositeanalysis x

  1. New Developments in Platelet Composite Rheology

    0.0 out of 5 stars 

    15 Feb 2023 | Contributor(s): Xuan Wang

  2. New Developments in Platelet Composite Performance

    0.0 out of 5 stars 

    15 Feb 2023 | Contributor(s): Xuan Wang

  3. New Developments in Platelet Meso-scale Measurements

    0.0 out of 5 stars 

    15 Feb 2023 | Contributor(s): Xuan Wang

  4. State of the Art of Rheology of Concentrated Suspensions

    0.0 out of 5 stars 

    14 Feb 2023 | Contributor(s): Xuan Wang

  5. Puck Failure Criteria

    0.0 out of 5 stars 

    31 Jul 2017

    Composite materials have been established as competitive materials during the last few decades due to their high strength to l ow weight ratio among other advantages and are widely used in many industries. A recent study has found that the industrial usage of composite failure...

  6. Injection Overmolding Manufacturing Process Simulation

    0.0 out of 5 stars 

    29 Jun 2017 | Online Presentations

    Injection over-molding or hybrid molding is a high-rate composites manufacturing process for fabrication of structural components with complex geometries.  The structural backbone is provided by a continuous-fiber woven prepreg while the geometric complexity is realized via injection...

  7. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  8. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  9. NAFEMS Invitation to Tender: How to Obtain Material Properties for Structural Analysis of Composites

    0.0 out of 5 stars 

    13 Feb 2015 | White Papers/Research Documents

    The NAFEMS Composites Working Group wishes to commission a new document with the suggested title "How to Obtain Material Properties for Structural Analysis of Composites". The book will be a companion volume to the existing NAFEMS publications "An introduction to the use of material models in...

  10. DiBenedetto Equation: Tg and DOC

    0.0 out of 5 stars 

    23 Jul 2014 | Tools

    DiBenedetto Equation: Glass Transition Temperature Dependence on Degree of Cure

  11. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  12. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  13. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  14. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  15. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    22 May 2013 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  16. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    23 Jul 2014 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  17. HyperSizer Pro Software from Collier Research

    0.0 out of 5 stars 

    22 May 2013 | Tool Information

    HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...

  18. Announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    Flyer announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop to be held at Purdue University, August 5-7, 2014.The Composites Design and Manufacturing HUB is holding a hands-on workshop in composites design, analysis and manufacturing. Join us at Purdue University on...

  19. Interlaminar Stresses in Symmetric Angle-Ply Laminates Subjected to Anticlastic Bending Deformation

    0.0 out of 5 stars 

    22 May 2013 | Tool Information

    The aim of the present work is to develop a solution for the interlaminar stress field in a symmetric and balanced,  angle-ply laminate subjected to anticlastic bending deformation.  Further, this class of problems is considered in order to elucidate the behavior of angle-ply laminates...

  20. Free-Edge Elasticity Solution: Tool Taxonomy and Evaluation

    0.0 out of 5 stars 

    22 May 2013 | White Papers/Research Documents

    A review of the free-edge elasticity solution tool, including tool taxonomy and evaluation.  An overview of the solution development is provided, followed by numerous examples of tool use and evaluation.  The document concludes with an evaluation of the tool maturity level.  The...