Resources: All

Submit a resource

Find a resource
  1. multiscalemodeling2canalysis2cprepregplateletcomposites2cbeamtheory x
  2. compositesdesign x
  3. compositeanalysis x
  4. beamtheory x
  5. compositesmanufacturing x

  1. Puck Failure Criteria

    0.0 out of 5 stars 

    31 Jul 2017

    Composite materials have been established as competitive materials during the last few decades due to their high strength to l ow weight ratio among other advantages and are widely used in many industries. A recent study has found that the industrial usage of composite failure...

  2. Injection Overmolding Manufacturing Process Simulation

    0.0 out of 5 stars 

    29 Jun 2017 | Online Presentations

    Injection over-molding or hybrid molding is a high-rate composites manufacturing process for fabrication of structural components with complex geometries.  The structural backbone is provided by a continuous-fiber woven prepreg while the geometric complexity is realized via injection...

  3. VABS: Powering Simple Beam Elements with Detailed 3D FEA Fidelity

    0.0 out of 5 stars 

    06 Jan 2017 | Downloads

    This presentation gives a brief introduction to VABS, a general-purpose cross-sectional analysis, which can power conventional, simple beam elements with detailed 3D FEA fidelity. 

  4. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  5. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  6. DiBenedetto Equation: Tg and DOC

    0.0 out of 5 stars 

    23 Jul 2014 | Tools

    DiBenedetto Equation: Glass Transition Temperature Dependence on Degree of Cure

  7. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  8. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  9. Keith Kedward and Composites Design (Slides)

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor Byron Pipes' slides from the 2014 ASC meeting at UCSD discussing Keith Kedward and Composites Design

  10. Keith Kedward and Composites Design (Recorded Talk)

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor Byron Pipes speaks at the 2014 ASC Conference at UCSD in tribute to Keith Kedward on the subject of Composites Design.

  11. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  12. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  13. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  14. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    22 May 2013 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  15. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    23 Jul 2014 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  16. HyperSizer Pro Software from Collier Research

    0.0 out of 5 stars 

    22 May 2013 | Tool Information

    HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...

  17. HyperSizer Pro Software from Collier Research

    0.0 out of 5 stars 

    23 Jul 2014 | Tool Information

    HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...

  18. Announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    Flyer announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop to be held at Purdue University, August 5-7, 2014.The Composites Design and Manufacturing HUB is holding a hands-on workshop in composites design, analysis and manufacturing. Join us at Purdue University on...

  19. Interlaminar Stresses in Symmetric Angle-Ply Laminates Subjected to Anticlastic Bending Deformation

    0.0 out of 5 stars 

    22 May 2013 | Tool Information

    The aim of the present work is to develop a solution for the interlaminar stress field in a symmetric and balanced,  angle-ply laminate subjected to anticlastic bending deformation.  Further, this class of problems is considered in order to elucidate the behavior of angle-ply laminates...

  20. Free-Edge Elasticity Solution: Tool Taxonomy and Evaluation

    0.0 out of 5 stars 

    22 May 2013 | White Papers/Research Documents

    A review of the free-edge elasticity solution tool, including tool taxonomy and evaluation.  An overview of the solution development is provided, followed by numerous examples of tool use and evaluation.  The document concludes with an evaluation of the tool maturity level.  The...