Resources: All

Submit a resource

Find a resource
  1. compositeanalysis x
  2. compositebeams x
  3. cdmhub x
  4. compositesmanufacturing x

  1. Injection Overmolding Manufacturing Process Simulation

    0.0 out of 5 stars 

    29 Jun 2017 | Online Presentations

    Injection over-molding or hybrid molding is a high-rate composites manufacturing process for fabrication of structural components with complex geometries.  The structural backbone is provided by a continuous-fiber woven prepreg while the geometric complexity is realized via injection...

  2. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  3. ANSYS-VABS Graphic User Interface (GUI)

    0.0 out of 5 stars 

    03 Aug 2015 | Downloads | Contributor(s): Gerhard Klimeck

    This resource contains the release package of ANSYS-VABS GUI.VABS code is NOT included. Manual and the source scripts for the interface can be found in the Supporting Documents.This GUI was developed based on ANSYS Release...

  4. CDM Hub Introduction

    0.0 out of 5 stars 

    17 Mar 2015 | Online Presentations | Contributor(s): SME Project

  5. DiBenedetto Equation: Tg and DOC

    0.0 out of 5 stars 

    23 Jul 2014 | Tools

    DiBenedetto Equation: Glass Transition Temperature Dependence on Degree of Cure

  6. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    18 May 2024 | Teaching Materials | Contributor(s): SME Project

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  7. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  8. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  9. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    22 May 2013 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  10. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    23 Jul 2014 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  11. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    18 May 2024 | Series | Contributor(s): SME Project

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  12. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    22 May 2013 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  13. HyperSizer Pro Software from Collier Research

    0.0 out of 5 stars 

    22 May 2013 | Tool Information

    HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...

  14. Nanohub and the HUBzero Platform

    0.0 out of 5 stars 

    18 May 2024 | Online Presentations | Contributor(s): SME Project

    Dr. Michael McLennan describes the nanoHUB and HUBzero platform at the May 2013 Composites Design and Manufacturing HUB workshop.

  15. PostGEBT

    0.0 out of 5 stars 

    30 May 2014 | Downloads | Contributor(s): Gerhard Klimeck

    PostGEBT is a post-processing code which can effectively visualize mass data generated by the nonlinear beam solver GEBT. PostGEBT reads and visualizes the results produced by GEBT for static, steady-state, transient dynamic, and eigenvalue analyses. More details can be found in the PostGEBT...

  16. The Challenge and Vision for cdmHUB

    0.0 out of 5 stars 

    18 May 2024 | Online Presentations | Contributor(s): SME Project

    Professor R. Byron Pipes presents the challenge and vision for the cdmHUB at the May 2013 Composites Design and Manufacturing HUB workshop

  17. Geometrically Exact Beam Theory

    2.5 out of 5 stars 

    30 May 2014 | Tools | Contributor(s): Gerhard Klimeck

    A General-Purpose Nonlinear Analysis Tool for Composite Beams Considering All Elastic Couplings

  18. Geometrically Exact Beam Theory

    0.0 out of 5 stars 

    11 Jul 2014 | Downloads | Contributor(s): Gerhard Klimeck

    Geometrically Exact Beam Theory (GEBT), is a general-purpose tool for nonlinear analysis of composite slender structures, meeting the design challenges associated with future engineering systems featuring highly-flexible slender structures made of composites. GEBT is based on the mixed...

  19. Announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop

    0.0 out of 5 stars 

    27 Jun 2014 | Teaching Materials

    Flyer announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop to be held at Purdue University, August 5-7, 2014.The Composites Design and Manufacturing HUB is holding a hands-on workshop in composites design, analysis and manufacturing. Join us at Purdue University on...

  20. Interlaminar Stresses in Symmetric Angle-Ply Laminates Subjected to Anticlastic Bending Deformation

    0.0 out of 5 stars 

    04 Jun 2014 | Tool Information

    The aim of the present work is to develop a solution for the interlaminar stress field in a symmetric and balanced,  angle-ply laminate subjected to anticlastic bending deformation.  Further, this class of problems is considered in order to elucidate the behavior of angle-ply laminates...