Resources: All

Submit a resource

Find a resource
  1. manufacturing x
  2. compositestructures x
  3. cdmhub x

  1. 2015 cdmHUB Workshop

    0.0 out of 5 stars 

    05 Jan 2016 | Series

    Composites Design, Analysis and Manufacturing Workshop held at Purdue University on November 3-5, 2015.  Both lectures slides and lecture videos are presented.

  2. Autocatalytic Degree of Cure -- Time and Temperature Data Point Entry

    0.0 out of 5 stars 

    27 Jun 2014 | Tools

    Calculates degree of cure based on time-temperature profile and autocatalytic cure model with Arrhenius rate-dependence from time and temperature data points.

  3. Autocatalytic Degree of Cure

    0.0 out of 5 stars 

    27 Jun 2014 | Tools

    Calculates degree of cure based on time-temperature profile and autocatalytic cure model with Arrhenius rate-dependence

  4. HyperSizer for Composites: Insanely Fast Laminate Optimization

    0.0 out of 5 stars 

    28 May 2014 | Tool Information

    95% of users, without user manual, and without instruction, will be able to import their FEM and produce optimum composites laminates that satisfy all analyses to all load cases within the first 10 minutes. Your automatically updated model will have minimum weight and fully producible laminates...

  5. CDM Hub Introduction

    0.0 out of 5 stars 

    19 May 2024 | Online Presentations | Contributor(s): SME Project

  6. CATIA Composites Braiding

    0.0 out of 5 stars 

    27 Jun 2014 | Animations

    A tool developed with BMW for strong structural Composites parts. Composites braiding is for high output cylindrical parts with minimal waste.

  7. Structure Genome: Fill the Gap between Materials Genome and Structural Analysis

    0.0 out of 5 stars 

    28 May 2014 | Publications

    A new concept, Structure Genome (SG), is proposed to fill the gap between materials genome and structural analysis. SG acts as the basic building block of the structure connecting materials to structures and the mechanics of SG governs the necessary information to link materials genome and...

  8. Variational Asymptotic Modeling of Composite Dimensionally Reducible Structures

    0.0 out of 5 stars 

    28 May 2014 | Publications

    This is Prof. Yu's PhD dissertation. In this disseration, the variational asymptotic method has be used to provide a systematic, holistic, and rigorous approach to construct efficient yet accurate models for composite beams, plates, and shells.  

  9. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    19 May 2024 | Teaching Materials | Contributor(s): SME Project

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  10. The Mission, Vision and Programs of the Composites Design and Manufacturing HUB

    0.0 out of 5 stars 

    28 May 2014 | Teaching Materials

    The presentation outlines the mission, vision and programs of the Composites Design and Manufacturing HUB as of October 2014.

  11. Composite Materials and Structures 1972-2012: Grand Challenges

    0.0 out of 5 stars 

    28 May 2014 | Teaching Materials

    Professor R. Byron Pipes presents the Grand Challenges for Composite Materials for the next 40 years at the American Society of Composites Conference in Arlington, TX on October 2, 2012.

  12. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    19 May 2024 | Series | Contributor(s): SME Project

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  13. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    28 May 2014 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  14. 2013 Composites Design and Manufacturing HUB Kickoff Workshop

    0.0 out of 5 stars 

    27 Jun 2014 | Series

    The Composites Design and Manufacturing HUB held a kick-off workshop at Purdue University on May 29-30, 2013 with over 100 attendees from industry, academia and government.  Select presentations from the workshop are included in this series.

  15. HyperSizer Pro Software from Collier Research

    0.0 out of 5 stars 

    28 May 2014 | Tool Information

    HyperSizer® is Design, Analysis, and Optimization Software for Composite and Metallic Structures HyperSizer is used throughout the design process--including certification--to quantify all critical failure modes, reduce structural weight, and sequence composite laminates for fabrication to...

  16. Nanohub and the HUBzero Platform

    0.0 out of 5 stars 

    19 May 2024 | Online Presentations | Contributor(s): SME Project

    Dr. Michael McLennan describes the nanoHUB and HUBzero platform at the May 2013 Composites Design and Manufacturing HUB workshop.

  17. The Challenge and Vision for cdmHUB

    0.0 out of 5 stars 

    19 May 2024 | Online Presentations | Contributor(s): SME Project

    Professor R. Byron Pipes presents the challenge and vision for the cdmHUB at the May 2013 Composites Design and Manufacturing HUB workshop

  18. Announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop

    0.0 out of 5 stars 

    27 Jun 2014 | Teaching Materials

    Flyer announcement for the 2014 Composites Design, Analysis and Manufacturing Workshop to be held at Purdue University, August 5-7, 2014.The Composites Design and Manufacturing HUB is holding a hands-on workshop in composites design, analysis and manufacturing. Join us at Purdue University on...